服务热线: 18367320777
您当前的位置:网站首页 > 新闻动态 > 公司新闻

盖板模具厂家-盖板塑料模具设备常见故障检查和排除方法

网站编辑:海盐华丰塑业有限公司 │ 发布时间:2020-03-28 

盖板塑料模具设备在矩形井的时候如果压力偏大我们应该先检查气压系统,再检查电磁阀及阀块。压力偏大会造成砖块的质量大大降低,我们一定要注意。当压力偏小的时候往往有可能是传感器的接线不正常导致的,当然也不能排除传感器被损坏或者PLC模块的线路出现问题或者物入点本身出现问题,在盖板塑料模具设备出现这种情况的时候一定要先关掉制砖机的开关,认真检查看看是否线路出现故障,找出原因调整好盖板塑料模具设备才可正常使用。

If the pressure is too high when the plastic mold equipment of the cover plate is in a rectangular well, we should first check the pneumatic system, and then check the solenoid valve and valve block. Partial pressure will greatly reduce the quality of bricks, we must pay attention. When the pressure is low, it is often possible that the wiring of the sensor is abnormal. Of course, it cannot be ruled out that the sensor is damaged or the PLC module has a problem or the entry point itself has a problem. This situation occurs in the plastic mold equipment of the cover. When it is time, you must first turn off the switch of the brick machine, check carefully to see if the circuit is faulty, find out the reason and adjust the cover plastic mold equipment before it can be used normally.

成型压力是有一定限度的。颗粒级配与极限压力。当物料颗粒级配良好,不同粒径的物料搭配使用,且颗粒较粗是,其极限压力就可以升高。用户所购买的盖板塑料模具设本身就是劣质产品,没有能够正常生产盖板塑料模具的能力。人们常说一分价钱一分货。所以要买就买好设备。每天模具停机后,应该将机台、料车、模具、输送带上的混凝土和脏污清理干净,保持生产线的清洁,确保第二天砖机设备能正常运转。每天开始运作模具块设备前,应检查一下模具设备紧固链接是否锁紧,电机接线端子是否松脱,油管是否漏油,皮带传送、送料方向是否阻挡。正常方可开机。

盖板塑料模具_盖板塑料模具厂家_华丰塑业

The molding pressure is limited. Particle gradation and ultimate pressure. When the gradation of the material particles is good, materials of different particle sizes are used together, and the particles are coarser, the ultimate pressure can be increased. The plastic cover molds purchased by users are inherently inferior products and do not have the ability to produce plastic cover molds normally. People often say that the price is equal to the price. So buy equipment if you want to buy it. Every day after the mold is shut down, the concrete and dirt on the machine, feed car, mold, and conveyor belt should be cleaned up to keep the production line clean and ensure that the brick machine equipment can operate normally the next day. Before starting the operation of the mold block equipment every day, check whether the fastening links of the mold equipment are tight, whether the motor terminals are loose, whether the oil pipe is leaking, and whether the belt transmission and feeding direction are blocked. Start up normally.